跳到主要内容

Digitable Tasks

Use for the shared Digitable backlog; close tasks by uuid.

Skill metadata​

SourceBundled (installed by default)
Pathskills/productivity/digitable-tasks
Version1.0.0
AuthorDigit
LicenseMIT
Platformslinux, macos
Tagstasks, tracker, taskwarrior, backlog, uuid, digitable
Related skillsdigitable-portal, digitable-engineering-docs

Reference: full SKILL.md​

信息

The following is the complete skill definition that Digit loads when this skill is triggered. This is what the agent sees as instructions when the skill is active.

Digitable Tasks

Overview​

The owner and several agents work one shared backlog — a Taskwarrior database in a .digitable-tasks tree beside the checkouts. digit tasks is the way in. Do not shell out to task directly: the wrapper exists to stop one specific mistake, and calling around it puts the mistake back.

When to Use​

  • Reading your assignment ("what is open in area X?")
  • Recording that something became true, with what proves it
  • Creating follow-up work you discovered but were not asked to do
  • Closing work you finished

The rule: uuid, never the number​

Taskwarrior prints a small integer beside every pending task and accepts it as a reference. That integer is positional. It is recomputed from the pending set, so closing one task renumbers the ones after it. A reference that was correct when you read it can point at a different task by the time you act on it. On 2026-08-04 seven agents in a row closed the wrong task this way.

digit tasks therefore refuses positional ids and exits 2 when it sees one. It refuses uuid prefixes too, and that part is not pedantry: Taskwarrior resolves unique prefixes, and a bare number is itself a valid hex prefix, so allowing prefixes would quietly re-admit the same mistake.

If you get exit 2, you do not need a workaround. You need the uuid, and digit tasks list prints it.

Commands​

digit tasks list                              # every open task, uuid first
digit tasks list --project DIGIT              # one area
digit tasks list --status completed           # what is already closed
digit tasks list --json                       # machine-readable

digit tasks show <uuid>                       # one task with its annotations

digit tasks add --project DIGIT 'what should become true'
digit tasks note <uuid> 'what proves it'
digit tasks done <uuid> --note 'what proves it'

add prints the uuid of the task it created. done --note records the annotation before changing the status, so a task is never left closed with no evidence attached.

Read the annotations before you work​

digit tasks show <uuid> is not optional. Earlier agents leave what they measured, what they decided, and what they deliberately did not do. Repeating work that an annotation already reports as done is the most common way to waste a session; contradicting a recorded decision is the most expensive.

Closing: what an annotation has to contain​

A verdict is a fact, not an impression. Before done, have one of:

  • a command that was run and its output ("scripts/run_tests.sh tests/x — 42 passed, 2.8s")
  • a commit sha
  • a grep that shows the thing exists, or does not

Write the numbers you measured, not the numbers a README claims. A course once shipped invented figures from exactly that shortcut and had to be cleaned out.

State what you did not do in the same annotation. A task closed with an unstated hole buys confidence it has not earned, and the next agent pays for it.

What this skill does not do​

  • It does not decide. A task marked as the owner's decision stays open. Say what the decision needs, and leave it.
  • It does not reassign or schedule. digit tasks covers listing, creation, annotation and closing. For anything else, ask.
  • It is not the kanban board. digit kanban is Digit's own SQLite board for dispatching work to profiles. This is the human-owned backlog. They are different databases and different lifecycles; do not mirror one into the other.

Where the tracker lives​

Resolution order: --data-dir, then tasks.data_dir in config.yaml, then TASKDATA (Taskwarrior's own variable, honoured so a user who already exports it does not have to repeat themselves), then the first .digitable-tasks/data directory found walking up from the working directory.

If none of those resolve, the command says so and names what it looked for — it does not silently create an empty tracker of its own.